Improvement of Electrical Conductivity of In Situ Iodine-Doped Polypyrrole Film Using Atmospheric Pressure Plasma Reactor with Capillary Electrodes.

To improve the electrical conductivity of polypyrrole (PPy) nanostructure film through in situ iodine (I2) doping, this study proposes an atmospheric pressure plasma reactor (APPR) where heated I2 dopant vapor is fed through capillary electrodes that serve as electrodes for discharge ignition. A large amount of the heated I2 vapor introduced into the reactor separately from a monomer gas can be effectively activated by an intense plasma via capillary electrodes. In particular, intensive plasma is obtained by properly adjusting the bluff body position in the APPR. Based on the ICCD and OES results, the I2 vapor injected through the capillary nozzle electrode is observed to form I2 charge species. The formed I2 species could directly participate in growing in situ I2-doped PPy films. Thus, in situ I2-doped PPy nanostructure films grown using the proposed APPR exhibit higher thicknesses of 15.3 µm and good electrical conductivities, compared to the corresponding non-doped films.

Characteristics of the Discoloration Switching Phenomenon of 4H-SiC Single Crystals Grown by PVT Method Using ToF-SIMS and Micro-Raman Analysis.

The discoloration switching appearing in the initial and final growth stages of 4H-silicon carbide (4H-SiC) single crystals grown using the physical vapor transport (PVT) technique was investigated. This phenomenon was studied, investigating the correlation with linear-type micro-pipe defects on the surface of 4H-SiC single crystals. Based on the experimental results obtained using time-of-flight secondary ion mass spectrometry (ToF-SIMS) and micro-Raman analysis, it was deduced that the orientation of the 4H-SiC c-axis causes an axial change that correlates with low levels of carbon. In addition, it was confirmed that the incorporation of additional elements and the concentrations of these doped impurity elements were the main causes of discoloration and changes in growth orientation. Overall, this work provides guidelines for evaluating the discoloration switching in 4H-SiC single crystals and contributes to a greater understanding of this phenomenon.

Fabrication and Characterization of Al2O3-Siloxane Composite Thermal Pads for Thermal Interface Materials.

In this study, Al2O3-siloxane composite thermal pads were fabricated using a tape-casting technique, and the thermal conductivity effect of the Al2O3 nanoparticle powder synthesized using a flame fusion process on siloxane composite thermal pads was investigated. Furthermore, various case studies were implemented, wherein the synthesized Al2O3 nanoparticle powder was subjected to different surface treatments, including dehydration, decarbonization, and silylation, to obtain Al2O3-siloxane composite thermal pads with high thermal conductivity. The experimental results confirmed that the thermal conductivity of the Al2O3-siloxane composite pads improved when fabricated using surface-treated Al2O3 nanoparticle powder synthesized with an optimally spheroidized crystal structure compared to that produced using non-treated Al2O3 nanoparticle powder. Therefore, this study provides guidelines for fabricating Al2O3-siloxane composite thermal pads with high thermal conductivity in the field of thermal interface materials.

Yeast-Hydrolysate-Derived 1-Methyl-1,2,3,4-tetrahydro-ß-carboline-3-carboxylic Acid Inhibits Fat Accumulation during Adipocyte Differentiation.

This study aimed to investigate the impact of yeast hydrolysate (YH) on lipogenesis, elucidate its mechanistic action, and identify the active compounds responsible for its anti-adipogenic effects. YH (2 mg/mL) significantly reduced Oil Red O-stained lipids. YH (2 mg/mL) also downregulated C/EBPß and upregulated KLF2, both of which are early adipogenic factors. Moreover, YH (2 mg/mL) decreased C/EBPα, PPARγ, FABP4, FAS, ACC, and HMGCR mRNA expression. Additionally, YH significantly downregulated SEBP1c and SREBP2 and their target genes, which govern fatty acid and cholesterol metabolism; however, 2 mg/mL YH had a greater suppressive effect on SREBP1c than on SREBP2. YH (2 mg/mL) also significantly reduced the mRNA level of G6PD and malic enzyme, which are enzymes that synthesize NADPH for lipid synthesis, compared with the control. Furthermore, 1-methyl-1,2,3,4-tetrahydro-ß-carboline-3-carboxylic acid (MTCA) was identified as the active compound with anti-adipogenic effects using solvent fractionation and chromatographic analysis of YH, and 1.1 µg/mL MTCA significantly downregulated SREBP1c/SREBP2 mRNAs by 47.8% and 69.2%, respectively, along with the target genes FAS, ACC, and HMGCR by 79.0%, 77.0%, and 40.9%, respectively. Collectively, YH effectively suppressed adipogenic lipid storage by downregulating SREBP- and NADPH-synthesizing genes. These findings suggest that YH containing MTCA has the potential to act as an anti-obesity agent.

Nutrient effects on drought responses vary across common temperate grassland species.

Drought and nutrient input are two main global change drivers that threaten ecosystem function and services. Resolving the interactive effects of human-induced stressors on individual species is necessary to improve our understanding of community and ecosystem responses. This study comparatively assessed how different nutrient conditions affect whole-plant drought responses across 13 common temperate grassland species. We conducted a fully factorial drought-fertilization experiment to examine the effect of nutrient addition [nitrogen (N), phosphorus (P), and combined NP] on species' drought survival, and on drought resistance of growth as well as drought legacy effects. Drought had an overall negative effect on survival and growth, and the adverse drought effects extended into the next growing season. Neither drought resistance nor legacy effects exhibited an overall effect of nutrients. Instead, both the size and the direction of the effects differed strongly among species and between nutrient conditions. Consistently, species performance ranking under drought changed with nitrogen availability. The idiosyncratic responses of species to drought under different nutrient conditions may underlie the seemingly contradicting effects of drought in studies on grassland composition and productivity along nutrient and land-use gradients-ranging from amplifying to dampening. Differential species' responses to combinations of nutrients and drought, as observed in our study, complicate predictions of community and ecosystem responses to climate and land-use changes. Moreover, they highlight the urgent need for an improved understanding of the mechanisms that render species more or less vulnerable to drought under different nutrients.

Effects of Continuous Nutrition Care on Nutritional Status and Dietary Habits of Patients With Colorectal Cancer Receiving Adjuvant Chemotherapy After Surgery.

Patients with colorectal cancer may experience symptoms such as diarrhea, nausea, and anorexia, during surgery and chemotherapy, which can increase the risk of malnutrition. In addition, dietary habits play a key role in the onset of colorectal cancer; therefore, it is necessary to improve dietary habits to prevent recurrence during treatment after diagnosis. In this study, a clinical nutritionist conducted 4 interviews for patients diagnosed with colorectal cancer and scheduled for colectomy: before surgery, after surgery, 1st chemotherapy, and 2nd chemotherapy, and provided nutrition care for each treatment course to determine its effects on nutrition status and disease prognosis. Significant weight loss but no decrease in muscle mass was observed during treatment. Body fat mass, although not statistically significant, showed a decreasing tendency. The percentage of people who responded 'yes' to the below items increased after compared to before receiving nutrition education: 'I eat meat or eggs more than 5 times a week,' 'I eat seafood at least three times a week,' 'I eat vegetables at every meal,' 'I eat fruits every day,' and 'I eat milk or dairy products every day.' These results indicate that the patients changed their dietary habit from a monotonous eating pattern to a pattern of consuming various food groups after receiving nutrition education. These results suggest that continuous nutrition care by clinical dietitians, according to the patient's treatment process, can help improve the patient's nutritional status and establish healthy eating habits.

Nanostructured Polyaniline Films Functionalized through Auxiliary Nitrogen Addition in Atmospheric Pressure Plasma Polymerization.

Polyaniline (PANI) was synthesized from liquid aniline, a nitrogen-containing aromatic compound, through the atmospheric pressure (AP) plasma process using a newly designed plasma jet array with wide spacing between plasma jets. To expand the area of the polymerized film, the newly proposed plasma jet array comprises three AP plasma jet devices spaced 7 mm apart in a triangular configuration and an electrodeless quartz tube capable of applying auxiliary gas in the center of the triangular plasma jets. The vaporized aniline monomer was synthesized into a PANI film using the proposed plasma array device. The effects of nitrogen gas addition on the morphological, chemical, and electrical properties of PANI films in AP argon plasma polymerization were examined. The iodine-doped PANI film was isolated from the atmosphere through encapsulation. The constant electrical resistance of the PANI film indicates that the conductive PANI film can achieve the desired resistance by controlling the atmospheric exposure time through encapsulation.

Yeast Hydrolysate and Postmenopausal Osteoporosis.

We used an ovariectomy (OVX) rat model to test whether yeast hydrolysate (YH) has therapeutic effects on postmenopausal osteoporosis-induced bone loss. The rats were separated into five treatment groups: the sham group (sham operation); the control group (no treatment after OVX); the estrogen group (estrogen treatment after OVX); YH 0.5% group (drinking water supplementation with 0.5% YH after OVX); and the YH 1% group (drinking water supplementation with 1% YH after OVX). In addition, the YH treatment restored serum testosterone concentration in the OVX rats up to the normal level. Further, YH treatment affected bone markers; a significant increase in serum calcium concentration was observed after adding YH to the diet. The levels of serum alkaline phosphatase, osteocalcin, and cross-linked telopeptides of type I collagen were reduced by YH supplementation, unlike those in the no-treatment control. Although not statistically significant, YH treatment in OVX rats improved trabecular bone microarchitecture parameters. These results show that YH may ameliorate the bone loss caused by postmenopausal osteoporosis because of the normalization of serum testosterone concentration.

Effect of freezing raw meat on the physicochemical characteristics of beef jerky.

The effect of freezing raw meat on the quality characteristics of beef jerky was evaluated in the present study. Jerky was made using different types of raw beef (fresh, frozen, and frozen-thawed) with different curing times (6 h and 12 h). Frozen-thawed beef had a lower moisture content than fresh or frozen beef due to higher exudate loss (P < 0.05). Jerky made using frozen and frozen-thawed beef showed lower drying yield and higher shear force than jerky prepared using fresh beef (P < 0.05). Freezing raw beef decreased the fat content and increased the redness, yellowness, chroma, and hue values of jerky (P < 0.05). The microstructure of beef jerky was showed to increase the deformation and contraction of muscle fibers due to freezing. Longer curing times increased the moisture content of jerky made using frozen meat (P < 0.05). Jerky made using frozen or frozen-thawed meat was tough due to excessive fat and moisture loss.

In vitro bioanalytical assessment of the occurrence and removal of bioactive chemicals in municipal wastewater treatment plants in Korea.

Effluents of wastewater treatment plants (WWTPs) contain various organic micropollutants, some of which can exert negative effects on the quality of receiving waters or drinking water sources. This study monitored two full-scale WWTPs in Korea for the occurrence and removal of bioactive chemicals for a one-year period using a battery of in vitro bioassays as a complementary approach to chemical analysis. Bioassays covering different endpoints were employed, such as hormone receptor activation (AR and ERα), xenobiotic metabolism (PAH and PXR), oxidative stress response (Nrf2), and cytotoxicity. The WWTP influents showed AR, ERα, and PAH activities at ng/L - µg/L and PXR and Nrf2 activities at µg/L - mg/L as bioanalytical equivalent concentrations of a reference compound for each bioassay. These bioactivities decreased along with the WWTP treatment train, with significant removals achieved by the secondary biological treatment processes. Cytotoxicity was observed only for some municipal wastewater (M-WWTP) influents but was below the limit of quantification for most cases. The influent and effluent bioactivities observed in this study were mostly comparable to those reported in other WWTPs in the literature. Comparison of the bioactivities with the effect-based trigger (EBT) values indicates that the impact of WWTP effluents on receiving water quality was low for most endpoints. For Nrf2, however, further investigation is required to evaluate the observed high bioactivities compared with the current EBT. The observed ERα activity could partly be explained by the presence of some steroid estrogens. Overall, our results contribute to an important database for the concentrations and removal efficiencies of bioactive chemicals in WWTPs and demonstrate bioassays as a useful tool for urban water quality monitoring.

Effects of Dielectric Barrier on Water Activation and Phosphorus Compound Digestion in Gas-Liquid Discharges.

To generate a stable and effective air-liquid discharge in an open atmosphere, we investigated the effect of the dielectric barrier on the discharge between the pin electrode and liquid surface in an atmospheric-pressure plasma reactor. The atmospheric-pressure plasma reactor used in this study was based on a pin-plate discharge structure, and a metal wire was used as a pin-type power electrode. A plate-type ground electrode was placed above and below the vessel to compare the pin-liquid discharge and pin-liquid barrier discharge (PLBD). The results indicated that the PLBD configuration utilizing the bottom of the vessel as a dielectric barrier outperformed the pin-liquid setup in terms of the discharge stability and that the concentration of reactive species was different in the two plasma modes. PLBD can be used as a digestion technique for determining the phosphorus concentration in natural water sources. The method for decomposing phosphorus compounds by employing PLBD exhibited excellent decomposition performance, similar to the performance of thermochemical digestion-an established conventional method for phosphorus detection in water. The PLBD structure can replace the conventional chemical-agent-based digestion method for determining the total dissolved phosphorus concentration using the ascorbic acid reduction method.

Development of an Atmospheric Pressure Plasma Jet Device Using Four-Bore Tubing and Its Applications of In-Liquid Material Decomposition and Solution Plasma Polymerization.

In this study, we describe an atmospheric pressure plasma jet (APPJ) device made of four-bore tubing operable in inhospitable humid environments and introduce two potential applications of liquid material processing: decomposition of aqueous phosphorus compounds and solution-plasma polymerization. A four-bore tube was used as the plasma transfer conduit and two diagonal bores contained metal wires. In the proposed APPJ device, the metal wires serving as electrodes are completely enclosed inside the holes of the multi-bore glass tube. This feature allows the APPJ device to operate both safely and reliably in humid environments or even underwater. Thus, we demonstrate that the proposed electrode-embedded APPJ device can effectively decompose aqueous phosphorus compounds into their phosphate form by directly processing the solution sample. As another application of the proposed APPJ device, we also present the successful synthesis of polypyrrole nanoparticles by solution plasma polymerization in liquid pyrrole.

Comparison of Meat Quality and Muscle Fiber Characteristics between Porcine Skeletal Muscles with Different Architectures.

This study aimed to compare the similarities, physicochemical properties, and muscle fiber characteristics of porcine skeletal muscles. Fourteen types of muscles were collected from nine pig carcasses at 24 h post-mortem and classified by muscle architecture into two main groups, namely parallel and pennate. The muscles were further differentiated into three subtypes per group. These included fan-shaped, fusiform, and strap for the parallel group, and unipennate, bipennate, and multipennate for the pennate group. Parallel-fibered muscles, which were composed of larger I, IIA, IIX, and IIXB fibers and a lower density of IIA fibers, showed higher redness and yellowness values than pennate-fibered muscles (p<0.05). However, the relative fiber area was not significantly different between the parallel and pennate groups (p>0.05). In the subtypes of parallel architecture, the strap group showed lower moisture content and higher redness values than the other subtypes and had considerably higher amounts of oxidative fibers (I and IIA; 72.3%) than the fan-shaped and fusiform groups (p<0.05). In the pennate group, unipennate showed comparatively lower moisture content and higher lightness than other pennate subtypes and was composed of smaller I, IIA, and IIX fibers than the bipennate and multipennate groups (p<0.05). Finally, a different trend of muscle clustering by hierarchical cluster analysis was found between physicochemical properties and muscle fiber characteristics. These results suggest that the physicochemical properties and muscle fiber characteristics of porcine skeletal muscles are not significantly dependent on morphological properties but are rather related to the intrinsic properties of the individual muscles.

Hierarchical deep learning model to simulate phytoplankton at phylum/class and genus levels and zooplankton at the genus level.

Harmful algal blooms (HABs) have become a global issue, affecting public health and water industries in numerous countries. Because funds for monitoring HABs are limited, model development may be an alternative approach for understanding and managing HABs. Continuous monitoring based on grab sampling is time-consuming, costly, and labor-intensive. However, improving simulation performance remains a major challenge in modeling, and current methods are limited to simulating phytoplankton (e.g., Microcystis sp., Anabaena sp., Aulacoseira sp., Cyclotella sp., Pediastrum sp., and Eudorina sp.) and zooplankton (e.g., Cyclotella sp., Pediastrum sp., and Eudorina sp.) at the genus level. The traditional modeling approach is limited for evaluating the interactions between phytoplankton and zooplankton. Recently, deep learning (DL) models have been proposed for solving modeling problems because of their large data handling capabilities and model structure flexibilities. In this study, we evaluated the applicability of DL for simulating phytoplankton at the phylum/class and genus levels and zooplankton at the genus level. Our work was an explicit representation of the taxonomic and ecological hierarchy of the DL model structure. The prerequisite for this model design was the data collection at two taxonomic and hierarchical levels. Our model consisted of hierarchical DL with classification transformer (TF) and regression TF models. These DL models were hierarchically connected; the output of the phylum/class level model was transferred to the genus level simulation model, and the output of the genus level model was fed into the zooplankton simulation model. The classification TF model determined the phytoplankton occurrence initiation date, whereas the regression TF model quantified the cell concentration of plankton. The hierarchical DL showed potential to simulate phytoplankton at the phylum/class and genus levels by producing average R2, and root mean standard error values of 0.42 and 0.83 [log(cells mL-1)], respectively. All simulated plankton results closely matched the measured concentrations. Particularly, the simulated cyanobacteria showed good agreement with the measured cell concentration, with an R2 value of 0.72. In addition, our simulated result showed good agreement in peak concentration compared to observations. However, a limitation remained in following the temporal variation of Tintinnopsis sp. and Bosmia sp. Using an importance map from the TF model, water temperature, total phosphorus, and total nitrogen were identified as significant variables influencing phytoplankton and zooplankton blooms. Overall, our study demonstrated that DL can be used for modeling HABs at the phylum/class and genus levels.

Optimization of Atmospheric Pressure Plasma Jet with Single-Pin Electrode Configuration and Its Application in Polyaniline Thin Film Growth.

This study systematically investigated an atmospheric pressure plasma reactor with a centered single pin electrode inside a dielectric tube for depositing the polyaniline (PANI) thin film based on the experimental case studies relative to variations in pin electrode configurations (cases I, II, and III), bluff-body heights, and argon (Ar) gas flow rates. In these cases, the intensified charge-coupled device and optical emission spectroscopy were analyzed to investigate the factors affecting intensive glow-like plasma generation for deposition with a large area. Compared to case I, the intense glow-like plasma of the cases II and III generated abundant reactive nitrogen species (RNSs) and excited argon radical species for fragmentation and recombination of PANI. In case III, the film thickness and deposition rate of the PANI thin film were about 450 nm and 7.5 nm/min, respectively. This increase may imply that the increase in the excited radical species contributes to the fragmentation and recombination due to the increase in RNSs and excited argon radicals during the atmospheric pressure (AP) plasma polymerization to obtain the PANI thin film. This intense glow-like plasma generated broadly by the AP plasma reactor can uniformly deposit the PANI thin film, which is confirmed by field emission-scanning electron microscopy and Fourier transform infrared spectroscopy.

Factors Affecting the Practice of Corona Virus Disease-19 Prevention Activities in Patients With Heart Diseases in Korea.

This study was conducted in a cross-sectional correlation design to identify factors affecting the practice of COVID-19 prevention activities in patients with heart diseases. A convenience sample of 195 patients with heart diseases from one tertiary teaching hospital completed questionnaires with items from the characteristics of these participants, their knowledge, attitude, and practice related to COVID-19 prevention activities. Participants' knowledge, attitude, and practice for COVID-19 prevention were relatively high but there was a significant difference in the degree of practice of COVID-19 prevention activities according to the characteristics of the participants. The higher the level of their knowledge and the more positive their attitude, the higher their practice. Attitude and information check about COVID-19 prevention were factors that influenced the practice of COVID-19 prevention activities, with an explanatory power of 32%. This study can help motivate and actively encourage COVID-19 prevention practices.

Potential Application of Pin-to-Liquid Dielectric Barrier Discharge Structure in Decomposing Aqueous Phosphorus Compounds for Monitoring Water Quality.

Here, we proposed a pin-to-liquid dielectric barrier discharge (DBD) structure that used a water-containing vessel body as a dielectric barrier for the stable and effective treatment of aqueous solutions in an open atmosphere. To obtain an intense pin-to-liquid alternating current discharge using a dielectric barrier, discharge characteristics, including the area and shape of a ground-plate-type electrode, were investigated after filling the vessel with equivalent amounts of water. Consequently, as the area of the ground electrode increased, the discharge current became stronger, and its timing became faster. Moreover, we proposed that the pin-to-liquid DBD reactor could be used to decompose phosphorus compounds in water in the form of phosphate as a promising pretreatment method for monitoring total phosphorus in water. The decomposition of phosphorus compounds using the pin-to-liquid DBD reactor demonstrated excellent performance-comparable to the thermochemical pretreatment method-which could be a standard pretreatment method for decomposing phosphorus compounds in water.

Gender Difference in the Relationship Between Pulse Pressure and Visceral Adiposity Index in Korean Adults.

Background: This study was conducted to assess the association of pulse pressure (PP) and visceral adiposity index (VAI) by gender in Korean adults. Methods: This study used the data of 4960 adults at age ≥20 years, from the 2015 Korean National Health and Nutrition Examination Survey. Results: In the overall population (n = 4960), after adjustment for related variables and with quartile 1 of VAI as a reference, the odds ratios of high PP (PP >60 mmHg) was significantly higher in quartile 3 [1.32 (95% confidence interval [CI], 1.02-1.71)] and quartile 4 of VAI [1.40 (95% CI, 1.07-1.83)]. In women (n = 2784), the OR of high PP, with quartile 1 of VAI as a reference, was significantly higher in quartile 3 [2.36 (95% CI, 1.55-3.61)] and quartile 4 of VAI [2.70 (95% CI, 1.77-4.12)]. In men (n = 2176), high PP was not associated with the quartiles of VAI. In addition, after adjustment for related variables, the PP level was positively associated with the quartiles of VAI in the overall population (P < 0.001) and women (P < 0.001), but not in men (P = 0.316). Conclusions: VAI was positively associated with PP in Korean women, but not in Korean men.

A Review of Plasma Synthesis Methods for Polymer Films and Nanoparticles under Atmospheric Pressure Conditions.

In this paper, we present an overview of recent approaches in the gas/aerosol-through-plasma (GATP) and liquid plasma methods for synthesizing polymer films and nanoparticles (NPs) using an atmospheric-pressure plasma (APP) technique. We hope to aid students and researchers starting out in the polymerization field by compiling the most commonly utilized simple plasma synthesis methods, so that they can readily select a method that best suits their needs. Although APP methods are widely employed for polymer synthesis, and there are many related papers for specific applications, reviews that provide comprehensive coverage of the variations of APP methods for polymer synthesis are rarely reported. We introduce and compile over 50 recent papers on various APP polymerization methods that allow us to discuss the existing challenges and future direction of GATP and solution plasma methods under ambient air conditions for large-area and mass nanoparticle production.

Ultrafast Room Temperature Synthesis of Porous Polythiophene via Atmospheric Pressure Plasma Polymerization Technique and Its Application to NO2 Gas Sensors.

New nanostructured conducting porous polythiophene (PTh) films are directly deposited on substrates at room temperature (RT) by novel atmospheric pressure plasma jets (APPJs) polymerization technique. The proposed plasma polymerization synthesis technique can grow the PTh films with a very fast deposition rate of about 7.0 µm·min-1 by improving the sufficient nucleation and fragment of the thiophene monomer. This study also compares pure and iodine (I2)-doped PTh films to demonstrate the effects of I2 doping. To check the feasibility as a sensing material, NO2-sensing properties of the I2-doped PTh films-based gas sensors are also investigated. As a result, the proposed APPJs device can produce the high density, porous and ultra-fast polymer films, and polymers-based gas sensors have high sensitivity to NO2 at RT. Our approach enabled a series of processes from synthesis of sensing materials to fabrication of gas sensors to be carried out simultaneously.